Band Properties - Intergraph Smart 3D - Reference Data - Hexagon PPM

Intergraph Smart 3D Hangers and Supports SmartParts Configuration

Language
English
Product
Intergraph Smart 3D
Subproduct
Hangers and Supports
Search by Category
Reference Data
Smart 3D Version
13

These properties define the band portion of the swivel ring. Some of these properties are optional. If they are left blank or set to zero, the part creates the dimension (or ignores the dimension) based on the rule provided.

IJUAhsWidth1::Width1

Specifies the first width for the swivel ring.

  • Standard Type - Enter the distance from the rod centerline to the edge of the lower top flange.

  • J Hanger Type - If Gap1 is greater than 0, then the hanger is a J Hanger. Enter the distance from the rod centerline to the edge of the top on the bolt side.

  • Adjustable Ring Type - If Width1 < 0.5 X RodDiameter and Width2 < 0.5 X RodDiameter, then the hanger is the adjustable ring type. There is no top flange. Width1 is not used. The bands have the space equal to the RodDiameter between them at the base of the top rod connection. By default, Width1 value is 1.5 X RodDiameter.

IJUAhsWidth2::Width2

Specifies the second width for the swivel ring.

  • Standard Type - Enter the distance from the rod centerline to the edge of the upper top flange.

  • J Hanger Type - If Gap1 is greater than 0, then the hanger is a J Hanger. Enter the distance from the rod centerline to the edge of the top which is not on the bolt side.

  • Adjustable Ring Type - If Width1 < 0.5 X RodDiameter and Width2 < 0.5 X RodDiameter, then the hanger is the adjustable ring type. There is no top flange. Width2 is not used. By default, the Width2 value is is 1.5 X RodDiameter.

IJUAhsWidth3::Width3

Specifies the width of the band or ring. This value must be greater than zero. By default, Width3 is 2 X RodDiameter.

IJUAhsThickness1::Thickness1

Specifies the thickness of the band or ring. This value must be greater than zero. By default, Thickness1 is 0.5 X RodDiameter.

IJUAhsHeight1::Height1

Specifies the distance from the pipe centerline to the bottom face of the lower flange. This value must be greater than 0.5 X PipeOD. By default, Height1 is PipeOD.

IJUAhsDiameter1::Diameter1

Specifies the inside diameter of the band if it differs from the PipeOD. If Diameter1 £ PipeOD, then use PipeOD as the inside diameter of the band or ring. In this case, the curve of the band is always 180 degrees.

IJUAhsGap1::Gap1

Specifies the distance between the two bolt ears for the J Hanger type. If Gap1 £ 0, then this is not a J Hanger so do not use Gap1.

IJUAhsWidth4::Width4

Enter the distance from the inside edge of the band to the outer edge of the upper bolt ear for the J Hanger type. If Gap1 is zero, then this is not a J Hanger so do not use Width4. If Gap1 < 0, then Width4 > Pin1Diameter + Thickness1. Otherwise, the software sets the default to 3 X (Pin1Diameter + Thickness1).

  • J Hanger type - top ear - The ears are drawn perpendicular from the band. The top portion of the band is drawn at the same angle so that a continuous band is drawn such that it meets up with the pipe at the correct position. The bottom ear is always 1.5 X Width4.

  • J Hanger type - bottom ear - The ears are drawn perpendicular from the band. The band needs to wrap around, and possibly extend away from, the pipe in order to make the correct gap. Both the ears are parallel.