The following properties are selection properties, which are useful to get the correct data about the current size, total travel, and load for the main part.
IJUAhsMinSize::MinSize
Specifies the minimum size to which the property values in this row apply.
IJUAhsMaxSize::MaxSize
Specifies the maximum size to which the property values in this row apply. The size properties must be included on all three reference tables. For example, if the Min Size = 1, Max Size = 4, and the current Size = 3, then the property values will be selected from this row.
IJUAhsMinTT::MinTT
Specifies the minimum travel to which these property values in this row apply.
IJUAhsMaxTT::MaxTT
Specifies the maximum travel to which these property values in this row apply. The TT properties must be included on the Travel Reference table. For example, if the MinTT = 1, MaxTT = 4, and the current TT = 3.5, then the values will be selected from this row.
IJUAhsTTUnitType::TTUnitType
Specifies the units of the total travel.
IJUAhsMinLoad::MinLoad
Specifies the minimum load to which these property values in this row apply.
IJUAhsMaxLoad::MaxLoad
Specifies the maximum load to which these property values in this row apply. The load properties must be included on the Load Reference table. For example, if the MinLoad = 0lbs, MaxLoad = 800lbs and the current Load = 750 lbs, then the values will be selected from this row.
IJUAhsRodDiameter::RodDiameter
Specifies the required rod diameter for the given size, total travel, or load.
IJUAhsHoleDiameter::HoleDiameter
Specifies the required hole diameter for the given size, total travel, or load.
IJUAhsLugHoleOffset::LugHoleOffset
Specifies the offset for the hole centerline from the edge of the lug. If it is set to zero or negative, the hole is centered on the lug.
IJUAhsGap1::Gap1
Specifies the required spacing between the double lugs of a type C constant.
IJUAhsGap2::Gap2
Specifies the required spacing between the double lugs of a type C constant for Lug 2 Shape.
IJUAhsLength::Length
Specifies the total length of the frame and casing. For more information, see Dimension Details.
IJUAhsOffset1::Offset1
Specifies the offset from the top connection port to the surface. For more information, see Dimension Details.
IJUAhsOffset2::Offset2
Specifies the offset of the port from the surface of the load column. For more information, see Dimension Details.
IJUAhsOffset3::Offset3
Specifies the offset from the edge of the load column to the center of the load column’s pivot pin. For more information, see Dimension Details.
IJUAhsOffset4::Offset4
Specifies the offset from the edge of the lever arm to the pivot pin. For more information, see Dimension Details.
IJUAhsOffset5::Offset5
Specifies the offset from the edge of the cross section of the column pin for Type G constant. For more information, see Dimension Details.
IJUAhsOffset6::Offset6
Specifies the offset from the top connection port to the surface. Offset6 is used only when lug2 shape is provided for Type C constant. For more information, see Dimension Details.
IJUAhsLength2::Length2
Specifies the length of the lever arm. For more information, see Dimension Details.
IJUAhsPlate1Offset::Plate1Offset
Specifies the position of Plate1. For more information, see Dimension Details.
IJUAhsPlate2Offset::Plate2Offset
Specifies the position of Plate2. For more information, see Dimension Details.
IJUAhsPlate3Offset::Plate3Offset
Specifies the position of Plate3. For more information, see Dimension Details.
IJUAhsPlate4Offset::Plate4Offset
Specifies the position of Plate4. For more information, see Dimension Details.
IJUAhsFrameOffset::FrameOffset
Specifies the offset of the frame from the casing. For more information, see Dimension Details.
IJUAhsCaseCLOffset::CaseCLOffset
Specifies the offset from the main pivot pin to the center line of the spring casing. For more information, see Dimension Details.
IJUAhsTopOffset::TopOffset
Specifies the offset from the main pivot pin to the top connection port. For more information, see Dimension Details.
IJUAhsPivotOffset::PivotOffset
Specifies the offset from the pivot to the edge of the frame. For more information, see Dimension Details.
IJUAhsTopSpacing::TopSpacing
Specifies the distance between the two top connection ports if the constant is double suspension. If the constant is single suspension, then this value is ignored. For more information, see Dimension Details.
IJUAhsFrameSpacing::FrameSpacing
Specifies the distance between the two frame plates. If this value is zero or negative, then only one plate is modeled.
IJUAhsLeverSpacing::LeverSpacing
Specifies the distance between the two lever plates. If this value is zero or negative, then only one plate is modeled.
IJUAhsLever2Offset::Lever2Offset
Specifies the vertical distance between the pins of the first and second levers in a type F constant.
IJUAhsGussetSpacing::GussetSpacing
Specifies the distance between the two gusset plates. If this value is zero or negative, then only one plate is modeled.
IJUAhsColumnSpacing::ColumnSpacing
Specifies the distance between the two column plates. If this value is zero or negative, then only one plate is modeled.
IJUAhsCCMin::CCMin
Specifies the minimum rod center to center distance for a type G constant.
IJUAhsCCMax::CCMax
Specifies the maximum rod center to center distance for a type G constant.
IJUAhsAngleHigh::AngleHigh
Specifies the angle of the lever arm from horizontal in the high position. For more information, see Dimension Details.
IJUAhsAngleLow::AngleLow
Specifies the angle of the lever arm from horizontal in the low position. For more information, see Dimension Details.
IJUAhsRodTakeOutHigh::RodTakeOutHigh
Specifies the rod take-out in the high position.
IJUAhsRodTakeOutLow::RodTakeOutLow
Specifies the rod take-out in the low position.
IJUAhsPlate1Shape::Plate1Shape
pecifies the name of a plate shape used to model Plate1. For more information, see Shape Details.
IJUAhsPlate2Shape::Plate2Shape
Specifies the name of a plate shape used to model Plate2. For more information, see Shape Details.
IJUAhsPlate3Shape::Plate3Shape
Specifies the name of a plate shape used to model Plate3. For more information, see Shape Details.
IJUAhsPlate4Shape::Plate4Shape
Specifies the name of a plate shape used to model Plate4. For more information, see Shape Details.
IJUAhsCasingShape::CasingShape
Specifies the name of a generic shape used to model the spring casing. For more information, see Shape Details.
IJUAhsFrameShape::FrameShape
Specifies the name of a plate shape used to model the frame. For more information, see Shape Details.
IJUAhsEarShape::EarShape
Specifies the name of a plate shape used to model the ears on a type D constant. For more information, see Shape Details.
IJUAhsGussetShape::GussetShape
Specifies the name of a plate shape used to model the gusset plates. For more information, see Shape Details.
IJUAhsLeverShape::LeverShape
Specifies the name of a plate shape used to model the lever plates. For more information, see Shape Details.
IJUAhsLever2Shape::Lever2Shape
Specifies the name of a plate shape used to model the second lever in a type F constant. For more information, see Shape Details.
IJUAhsUpThrustShape::UpThrustShape
Specifies the name of a plate shape used to model the up-thrust plates on a type U constant. For more information, see Shape Details.
IJUAhsPivotPinShape::PivotPinShape
Specifies the name of a pin shape used to model the main pivot pin. For more information, see Shape Details.
IJUAhsColumnPinShape::ColumnPinShape
Specifies the name of a pin shape used to model the load column pin. For more information, see Shape Details.
IJUAhsColumnShape::ColumnShape
Specifies the name of a rod shape used to model the load column. For more information, see Shape Details.
IJUAhsColumnEndShape::ColumnEndShape
Specifies the name of a nut shape used to model the end of the load column. For more information, see Shape Details.
IJUAhsColumnNutShape::ColumnNutShape
Specifies the name of a nut shape used to model the nut at the bottom of the load column. For more information, see Shape Details.
IJUAhsClevisShape::ClevisShape
Specifies the name of a clevis shape used to model a clevis or yoke at the top of the load column. For more information, see Shape Details.
IJUAhsTurnbuckleShape::TurnbuckleShape
String specifying the name of a turnbuckle shape used to model a turnbuckle or coupling at the bottom of the load column rod. For more information, see Shape Details.
IJUAhsColumnPlateShape::ColumnPlateShape
String specifying the name of a plate shape used to model the load column. For more information, see Shape Details.
IJUAhsTopAttachment::TopAttachment
Specifies the top of the type F load column. For more information, see Shape Details.
IJUAhsNutShape::NutShape
Specifies a nut to be used with the type A constant. For more information, see Shape Details.
IJUAhsLugShape::LugShape
Specifies the lug used with a type B or C constant. For more information, see Shape Details.
IJUAhsLug2Shape::Lug2Shape
Specifies the lug used with a Type C Constant. Lug2Shape is used only when a single lug is required for Type C constant. For more information, see Plate.
IJUAhsPinShape::PinShape
Specifies a pin used with the lug2 shape of a type C constant. For more information, see Pin.
IJUAhsPin2Shape::Pin2Shape
Specifies a pin used with the lug shape of type B or C constant. For more information, see Shape Details.
IJUAhsStructAttachment::StructAttachment
Specifies an optional structural attachment, such as a WBA or lug, which connects to the pin of a type B or C constant.