Question |
Type |
Flip |
BooleanCol (codelist) |
Flip Primary and Secondary |
BooleanCol (codelist) |
Flip
Flips the location of asymmetrically applied features when the member is symmetrically bound.
FlipPrimaryandSecondary
Changes the end cuts from primary to secondary, and from secondary to primary. This applies in end-to-end cases in which you place an assembly connection.
Items
The naming convention for the items is a prefix that indicates primary usage with respect to the alignment of the bounded and bounding members followed by a sequential number. For example, F0001, FE0007, EE0003, and so on. The terms used to describe alignment are the same as those used for the existing question-and-answer-based assembly connections.
-
F = To Face
-
FE = To Face and Edge
-
EE = To Edge and Edge
-
EX = To Edge and Outside
-
FO = To Face and Outside
-
XX = To Outside and Outside
-
S = Collinear Seam
-
X = Special Case
-
OM = On Member
-
FX = Face and Outside
-
SN = Split None
Name |
Description |
Figure |
---|---|---|
E0001 |
This assembly connection places a sniped flange cut at the top, and a straight flange cut at the bottom. The web is cut along the bounding member, and required physical connections are created. |
|
EE0001 |
This assembly connection places a straight flange cut at the top and bottom. It also places a corner feature (cope) at the top and bottom, and a snipe corner feature at the top face corner and bottom face corners. |
|
EE0002 |
This assembly connection places a straight flange cut at the top and bottom. It also places a corner feature (face to outside) at the top and bottom. |
|
EE0003 |
This assembly connection places a straight flange cut at the top and bottom. It also places a corner feature (cope) at the top and (rathole) at the bottom. |
|
EE0004 |
This assembly connection places a straight flange cut at the top and bottom. It also places a corner feature (face to outside) at the top and (face to inside) bottom. |
|
EE0005 |
This assembly connection places a straight flange cut and a corner feature (cope) at the top and bottom. |
|
EE0006 |
This assembly connection places a straight flange cut and a corner feature (face to inside) at the top and bottom. |
|
EE0007 |
This assembly connection places a straight flange cut at the top and bottom. It also places a corner feature (edge to outside) at the bottom. |
|
EE0008 |
This assembly connection places a straight flange cut at the top and bottom. It also places a corner feature (face to outside) at the bottom, and a snipe corner feature at the top face corner. |
|
EE0009 |
This assembly connection places a straight flange cut at the top and bottom. |
|
EE0010 |
This assembly connection places a straight flange cut at the top and bottom. It also places a corner feature (Inside Face Rathole Std) at the top and (Inside Face Rathole Std) bottom. |
|
EE1001 |
This assembly connection places a straight flange cut at the top and bottom. It also places corner features at the top face, bottom face, and inside edge. |
|
EE1002 |
This assembly connection places a straight flange cut at the top and a snipe flange cut at the bottom. It also places corner features at the top face, bottom face, and inside edge. |
|
EE1003 |
This assembly connection places a snipe flange cut at the top and bottom. It also places corner features at the top face, bottom face, and inside edge. |
|
EE1004 |
This assembly connection places a snipe flange cut at the top and a straight flange cut at the bottom. It also places corner features at the top face, bottom face, and inside edge. |
|
EX0001 |
This assembly connection places a straight flange cut at the top and bottom. It also places a corner feature (face to outside) at the top and (cope) bottom, and a snipe corner feature at the top face corner. |
|
EX1001 |
This assembly connection places a straight flange cut at the top and bottom. It also places an outside web cut and corner features at the top face corner, the bottom face corner, and the inside edge. |
|
EX1002, EX1003 |
This assembly connection places a straight flange cut at the top and bottom. It also places an outside web cut and corner features at the top face corner, the bottom face corner, and the inside edge. |
|
EX1004 |
This assembly connection places a straight flange cut at the top and bottom. It also places an outside web cut and corner features at the top face corner, the bottom face corner, and the inside edge. |
|
EX1005 |
This assembly connection places a snipe flange cut at the outside flange and a straight flange cut on the other flange. It also places an outside web cut and corner features at the top face corner, the bottom face corner, and the inside edge. |
|
EX1006, EX1007 |
This assembly connection places a snipe flange cut at the outside flange and a straight flange cut on the other flange. It also places an outside web cut and corner features at the top face corner, the bottom face corner, and the inside edge. |
|
EX1008 |
This assembly connection places a snipe flange cut at the outside flange and a straight flange cut on the other flange. It also places an outside web cut and corner features at the top face corner, the bottom face corner, and the inside edge. |
|
EX1009 |
This assembly connection places a snipe flange cut at the outside flange and a straight flange cut on the other flange. It also places an outside web cut and corner features at the top face corner, the bottom face corner, and the inside edge. |
|
EX1010, EX1011 |
This assembly connection places a snipe flange cut at the outside flange and a straight flange cut on the other flange. It also places an outside web cut and corner features at the top face corner, the bottom face corner, and the inside edge. |
|
EX1012 |
This assembly connection places a snipe flange cut at the outside flange and a straight flange cut on the other flange. It also places an outside web cut and corner features at the top face corner, the bottom face corner, and the inside edge. |
|
F0001 |
This assembly connection places a straight flange cut at the top and bottom. |
|
F0002 |
This assembly connection places sniped setback flange cuts at the top and bottom. |
|
F0003 |
This assembly connection places a straight flange cut at the top and a sniped setback at the bottom. |
|
F0004 |
This assembly connection places a straight flange cut at the top and a sniped cut at the bottom. |
|
F0005 |
This bearing plate assembly connection has a rectangular cross-section bearing plate with a particular value of radius and offset given for W-type cross-sections. |
|
F0006 |
This bearing plate assembly connection has a circular cross-section bearing plate with a proper radius given for Circular type cross-sections. |
|
F0007 |
This bearing plate assembly connection has a triangular cross-section bearing plate with a particular value of radius and offset given for L-type cross-sections. |
|
F0008 |
This bearing plate assembly connection has a rectangular cross-section bearing plate and circular endings with a particular value of radius and offset given for flat bar type cross-sections |
|
F0009 |
This assembly connection places a straight flange cut at the top and bottom. |
|
F0010 |
This assembly connection places a slot on the bounding member and end cuts on the bounded member. |
|
F0011 |
This assembly connection places only a slot on the bounding member. This connection does not alter the length of the member system by applying an extension or setback to the member part. The dimension X in the graphic is determined by the placement of the bounding and bounded members. |
|
F0014 |
This bearing plate assembly connection has a rectangular cross-section bearing plate with a specific radius and offset value. |
|
F1001 |
This assembly connection places a straight flange cut at the top and bottom. |
|
F1002 |
This assembly connection places a snipe flange cut at the top and bottom. |
|
F1005 |
This assembly connection places a SnipeCutStd_WebcutPoint_R flange cut at the top and bottom. |
|
F1006 |
This assembly connection places an OffsetSnipeCutStd_WebcutPoint_R flange cut at the top and bottom. |
|
F1007 |
This assembly connection places an OffsetSnipeCutStd_Nose_WebcutPoint_R flange cut at the top and bottom. |
|
FE0001 |
This assembly connection places a sniped setback flange cut at the bottom. It also places a straight flange cut and a corner feature (cope) at the top, and a snipe corner feature at the top face corner. |
|
FE0002 |
This assembly connection places a sniped flange cut at the bottom. It also places a straight flange cut and a corner feature (face to outside) at the top. |
|
FE0003 |
This assembly connection places a straight flange cut at the top and bottom. It also places a corner feature (cope) at the top and a snipe corner feature at the top face corner. |
|
FE0004 |
This assembly connection places a straight flange cut at the top and bottom. It also places a corner feature (face to outside) at the top. |
|
FE0005 |
This assembly connection places a sniped setback flange cut at the bottom. It also places a straight flange cut and a corner feature (rathole) at the top, and a snipe corner feature at the top face corner. |
|
FE0006 |
This assembly connection places a sniped flange cut at the bottom. It also places a straight flange cut and a corner feature (face to inside) at the top. |
|
FE0007 |
This assembly connection places a straight flange cut at the top and bottom. It also places a corner feature (rathole) at the top, and a snipe corner feature at the top face corner. |
|
FE0008 |
This assembly connection places a straight flange cut at the top and bottom. It also places a corner feature (face to inside) at the top. |
|
FE0009 |
This assembly connection places a straight flange cut at the top and bottom. It also places a corner feature (cope) at the top, and a snipe corner feature at the top face corner. |
|
FE0010 |
This assembly connection places a sniped setback flange cut at the bottom and a straight flange cut at top, and a snipe corner feature at the top face corner. |
|
FE0011 |
This assembly connection places a sniped setback flange cut at the bottom. It also places a straight flange cut and a corner feature (cope) at the top, and a snipe corner feature at the top face corner. |
|
FE0012 |
This assembly connection places a straight flange cut at the top and bottom, and a snipe corner feature at the top face corner. |
|
FE0013 |
This assembly connection places a sniped flange cut at the bottom. It also places a straight flange cut and a corner feature (cope) at the top, and a snipe corner feature at the top face corner. |
|
FE1001 |
This assembly connection places a straight flange cut at the top and bottom. It also places corner features at the top face, bottom face, and inside edge. |
|
FE1002 |
This assembly connection places a straight flange cut at the top and a snipe flange cut at the bottom. It also places corner features at the top face, bottom face, and inside edge. |
|
FE1003 |
This assembly connection places a straight flange cut at the top and bottom. It also places a cope feature at the bottom, and corner features at the top face and inside edge. |
|
FE1004 |
This assembly connection places a straight flange cut at the top, and a snipe flange cut at the bottom. It also places a cope feature at the bottom, and corner features at the top face and inside edge. |
|
FX0001 |
This assembly connection places a web cut that is sniped back starting at an offset from the outside surface. |
|
FX1001 |
This assembly connection places a bottom web cut sniped from the outside surface point offset. It also places straight flange cuts at the top and bottom. |
|
FX1002 |
This assembly connection places a bottom web cut sniped from the outside surface point offset. It also places a straight flange cut at the top and a snipe flange cut at the bottom. |
|
FX1003 |
This assembly connection places a bottom web cut sniped from the outside surface point offset. It also places a straight flange cut at the top and bottom. |
|
M0001 |
This assembly connection places bisecting cuts. It applies whenever two identical members are connected end-to-end. |
|
OM0001 |
This assembly connection is given with straight web and flange cuts for cross-sections such as W, L, T, PIPE, RS, and so on. |
|
OM1001 |
This assembly connection places an extended part where the bounding object is a plate part and the bounding object and plate part boundary are the same. |
|
OM1002 |
Creates a lapped assembly connection between the member and the profile. |
N - Lap length |
S0001 |
This assembly connection places a straight flange cut at the top and bottom. |
|
S0002 |
This assembly connection places straight web and flange cuts with a gap of 250 mm. It applies whenever two identical members are collinear and attached end-to-end. You can adjust the gaps after placement. |
|
S1001 |
This assembly connection places an extended straight web cut on the primary member, and a setback straight web cut on the secondary member. It also places straight flange cuts for the primary and secondary member's top and bottom flanges. This Smart item is available by rule when the input members are collinear and attached end to end. You can adjust the extension and setback values using the end cut properties. |
|
S1002 |
This assembly connection places an extended straight web cut on one member and a setback straight web cut on the other member. It also places step snipe flange cuts on the primary member top and bottom flanges, and a straight flange cut on the secondary member. This Smart item is available by rule when the input members are collinear and attached end to end. You can adjust the extension and setback values using the end cut properties. |
|
S1003 |
This assembly connection places a straight web cut on both members. It also places chamfered step snipe flange cuts for the primary member top and bottom flanges, and straight flange cuts on the secondary member.
|
|
S1004 |
This assembly connection places an extended straight web cut on the primary member. It also places a setback straight web cut for the secondary member, and right snipe flange cuts for the primary and secondary members' top and bottom flanges. This Smart item is available by rule when the input members are collinear and attached end to end. Select this Smart item by rule when the member cross sections are different. You can adjust the extension and setback values using the end cut properties. |
|
S1005 |
This assembly connection places an extended straight web cut on the primary member. It also places a straight web cut for the secondary member, and left and right snipe flange cuts for the primary and secondary members' top and bottom flanges. This Smart item is available by rule when the input members are collinear and attached end to end. Select this Smart item by rule when the member cross sections are different. You can adjust the extension and setback values using the end cut properties. |
|
S1006 |
This assembly connection places a straight web cut on primary and secondary members. It also places step snipe flange cuts on the primary member top and bottom flanges. This Smart item is available by rule when the input members are collinear and attached end to end. Select this Smart item by rule when the member flange widths are different. |
|
S1007 |
This assembly connection places an angled web cut between two members. It also places chamfered step snipe flange cuts for the primary member top and bottom flanges, and straight flange cuts on secondary member top and bottom flanges. This Smart item is available by rule when the input members are collinear, have different cross sections, and are attached end to end. |
|
S1008 |
This assembly connection places an angled web cut between two members. It also places chamfered step snipe flange cuts for the primary member top and bottom flanges, and straight flange cuts on secondary member top and bottom flanges. This Smart item is available by rule when the input members are collinear, have different cross sections, and are attached end to end. |
|
S1009 |
This assembly connection places a straight web cut on primary and secondary members. It also places chamfered step snipe flange cuts for the primary member top and bottom flanges, and straight flange cuts on the secondary member top and bottom flanges. This Smart item is available by rule when the input members are collinear, have different cross sections, and are attached end to end. |
|
S1010 |
This assembly connection places an angled web cut between members. It also places chamfered step snipe flange cuts for the primary member top and bottom flanges, and straight flange cuts on the secondary member top and bottom flanges. This Smart item is available by rule when the input members are collinear, have different cross sections, and are attached end to end. |
|
S1011 |
This assembly connection places an angled web cut between members. It also places step snip flange cuts for the primary member top and bottom flanges, and straight flange cuts on the secondary member top and bottom flanges. This Smart item is available by rule when the input members are collinear, have different cross sections, and are attached end to end. |
|
S1012 |
This assembly connection places an angled web cut between members. It also places right snipe flange cuts for the primary member top and bottom flanges, and straight flange cuts for the secondary member top and bottom flanges. This Smart item is available by rule when the input members are collinear, have different cross sections, and are attached end to end. |
|
S1013 |
This assembly connection places an angled web cut between members. It also places right snipe flange cuts for the primary member top and bottom flanges, and straight flange cuts for the secondary member top and bottom flanges. This Smart item is available by rule when the input members are collinear, have different cross sections, and are attached end to end. |
|
S1014 |
This assembly connection places an angled web cut between members. It also places right snipe cuts for the primary member top and bottom flanges, and straight flange cuts on the secondary member top and bottom flanges. This Smart item is available by rule when the input members are collinear, have different cross sections, and are attached end to end. |
|
S1015 |
This assembly connection places a straight web cut on primary and secondary members. It also places left snipe flange cuts for the primary member top and bottom flanges, and straight flange cuts on the secondary member top and bottom flanges. This Smart item is available by rule when the input members are collinear, have different cross sections, and are attached end to end. |
|
S1016 |
This assembly connection places an angled web cut between members. It also places left snipe flange cuts for the primary member top and bottom flanges, and straight flange cuts on the secondary member top and bottom flanges. This Smart item is available by rule when the input members are collinear, have different cross sections, and are attached end to end. |
|
S1017 |
This assembly connection places an angled web cut between members. It also places left snipe flange cuts for the primary member top and bottom flanges, and straight flange cuts on the secondary member top and bottom flanges. This Smart item is available by rule when the input members are collinear, have different cross sections, and are attached end to end. |
|
S1018 |
This assembly connection places a straight flange cut at the top and a sniped setback at the bottom. |
|
S1019 |
This assembly connection places a straight flange cut at the top and a sniped cut at the bottom. |
|
SN0001 |
This assembly connection places a lap physical connection between bounded and bounding. |
|
X0001 and X0002 |
This set of end cuts is for shaping parts within the flanges of the reference (hatched) member. Two overlapping parts, Part 1 and Part 2, are placed manually (typically using PinPoint). The parts must be centered on the reference web, each oriented with the top surface outward. Part 1 and Part 2 must have end-to-end frame connections at each end. There is no connection between Part 1 or Part 2 and the reference member. X0001A or X0002A should be placed at one end, and X0001B or X0002B at the opposite end. Each connection trims the ends of both members. X0001A and X00002A also remove the bottom portion of each member. Physical connections are created manually. |
|
XX0001 |
This assembly connection places a sniped web cut and flange cuts at the top and bottom of the bounded standard member. |
|
XX0002 |
This assembly connection places a hook type web cut and a straight flange cut at the top and bottom. It also places a snipe corner feature at the top and bottom face corners. |
|
X0003 |
This assembly connection places sniped flange cuts at the top and bottom. It also places a sniped web cut at the top and bottom, and a straight web cut at the center. |
Table 1: Flange Fillet Weld |
|
---|---|
Bounded Thickness |
Fillet Leg Length (W) |
0 mm < BT <= 8 mm |
8 mm |
8 mm < BT <= 10 mm |
10 mm |
10 mm < BT <= 12 mm |
12 mm |
12 mm < BT <= 15 mm |
15 mm |
15 mm < BT <= 20 mm |
20 mm |
20 mm < BT <= 25 mm |
25 mm |
30 mm < BT |
30 mm |
Table 2: Web Fillet Weld |
|
Bounded Thickness |
Fillet Leg Length (W) |
0 mm < BT <= 10 mm |
5 mm |
10 mm < BT <= 12 mm |
6 mm |
12 mm < BT <= 15 mm |
8 mm |
15 mm < BT <= 20 mm |
10 mm |
20 mm < BT <= 25 mm |
12 mm |
25 mm < BT <= 30 mm |
15 mm |
30 mm < BT |
20 mm |
Table 3 |
|
---|---|
Flange Width (FW) |
Nose (N) |
FW <= 150 mm |
25 mm |
150 mm < FW |
50 mm |
Connections
Connections apply to all cross-sections, unless otherwise noted. If the symbols in the table below display next to a part, that part is limited to those sections. If multiple designations apply, they are shown separated by a comma. If a minus sign ( - ) precedes the designations, the connection applies to all cross-sections except those listed. For example, -BU indicates that all cross-sections except for the Built-Up Angle apply to the connection.
Angle (all types) |
|
Angle X-Type |
|
Box (all types) |
|
Box (extruded) |
|
Built-Up Angle |
|
Built-Up Box |
|
Built-Up Channel |
|
Built-Up I-Beam |
|
Built-Up Tee |
|
Bulb Angle |
|
Bulb Tee |
|
Channel (all types) |
|
Channel S-Type |
|
Channel X-Type |
|
Flat Bar |
|
Half-Round Bar |
|
I-Beam (all types) |
|
I-Beam S-Type |
|
I-Beam X-Type |
|
Rectangular Bar |
|
Round Bar |
|
Round Tube |
|
Tee (all types) |
|
Tee S-Type |
|
Tee X-Type |