A Trunnion assembly uses the following dimensions.
Input Dimensions
You can set the default values for the input dimensions in the support definition sheet. If the attributes are OAs, then you can modify the attribute values on the Support Occurrence Property page.
Name |
User Name |
Category |
On Property Page |
Read Only |
---|---|---|---|---|
TrunnionAngle1 |
Trunnion Angle 1 |
Dimensions |
Yes |
No |
TrunnionAngle2 |
Trunnion Angle 2 |
Dimensions |
Yes |
No |
OverhangDefinition |
Overhang - Definition |
Dimensions |
Yes |
No |
Overhang2 |
Overhang 2 |
Dimensions |
Yes |
No |
Overhang2Rule |
Overhang 2 Rule |
Dimensions |
Yes |
No |
Overhang2Selection |
Overhang 2 Selection |
Dimensions |
Yes |
No |
Overhang2Definition |
Overhang 2 Definition |
Dimensions |
Yes |
No |
Attribute Name |
Description |
Implementation Details |
---|---|---|
IJUAhsTrunAngle1:: |
Specifies the angle for Trunnion 1. |
Angle is measured clockwise and negative values are supported. |
IJUAhsTrunAngle1:: |
Specifies the angle for Trunnion 2, if present. |
Angle is measured clockwise and negative values are supported. |
IJUAhsTrunOHDef:: |
Specifies the overhang for the trunnion. |
1 - Center of Steel to Pipe End 2 - Inside Edge of Steel to Pipe End 3 - Outside Edge of Steel to Pipe End 4 - Center of Steel to Cap Plate End 5 - Inside of Steel to Cap Plate End 6 - Outside of Steel to Cap Plate End |
IJUAhsTrunOH::Overhang IJUAhsTrunOHRl:: IJUAhsTrunOHSel:: |
Specifies the overhang of the Trunnion support. |
|
IJUAhsTrunOH2:: |
Specifies the overhang for Trunnion 2 support. |
|
IJUAhsTrunOH2Def:: |
Specifies the overhang for Trunnion 2. |
|
IJUAhsTrunShoeHt:: IJUAhsTrunShoeHtRl:: IJUAhsTrunShoeHtSel:: |
Specifies the Shoe height of the Trunnion support. |
|
IJUAhsCapInset::CapInset IJUAhsCapInsetRl:: IJUAhsCapInsetSel:: |
Specifies the inset of the Cap Plate. You can use this attribute only if the Cap configuration is Internal. |
|
IJUAhsFrameClampPart::ClampPart IJUAhsFrameClampRI::ClampRule |
Specifies the clamp part number or part class which needs to be added as an attachment. To select the part number using ClampRule, do not type any value for this property. |
|
IJUAhsFrameShearLug::ShearLug |
Specifies the ShearLug part number or part class which needs to be added as an attachment. |
Output Dimensions
The following output dimensions values are determined by Smart 3D and are displayed in the property page as read-only properties.
Attribute Name |
Description |
Implementation Details |
---|---|---|
IJUAhsTrunnionLen1:: |
Specifies the length of Trunnion 1 support.
The software automatically determines the value if TrunnionLength1 based on the location of the primary supporting structure. If the primary supporting structure is a slab, then you can type the length of the trunnion. |
|
IJUAhsTrunnionLen2:: |
Specifies the length of the second Trunnion, if applicable.
If there is a second supporting structure, the software automatically determines the TrunnionLength2. If no second supporting structure exists or the second supporting structure is a slab, then you can manually enter the length for the second Trunnion. |
For more information, see TrunnionLength1. |
For more information on how to use dimensional attributes, see Input Values.