Attribute Name |
Description |
Implementation Details |
---|---|---|
IJUAhsLeg1::Leg1Part |
Specifies the part number or the part class of the first leg. |
Leg 1 is a mandatory part. You must specify either Leg1Part or Leg1Rule. |
IJUAhsLeg1Ang:: |
Specifies a codelist value for the angle of rotation of the first leg support. The angle is about the axis of the leg. |
hsSteelOrientationAngle |
IJUAhsLeg1Rl::Leg1Rule |
Defines an HgrSupportRule that returns a rich hanger beam part number. To select the part number using Leg1Part, do not type any value for this property. |
|
IJUAhsLeg1BeginOH:: |
Specifies the distance between the first leg and the main member. The distance must be a positive number. |
The following values are supported: 1 - External Edge of Steel 2 - Centerline of Steel 3 - Internal Edge of Steel 4 - Primary Pipe Centerline |
IJUAhsLeg1BeginOHRl:: Leg1BeginOverhangRule |
Defines an HgrSupportRule that returns the distance that the first leg should overhang past the main member. The hanger rule should exist in the catalog; it can be a rule name or a ProgID. The rule must return the value in the DB Units (meters). To select the overhang value directly using Leg1BeginOverhangValue, do not type any value for this property. |
|
IJUAhsLeg1BeginOHDef:: Leg1BeginOverhangDefinition |
Defines how the begin overhang should be measured. |
Allowed values are shown below: |
IJUAhsLeg1BeginOHSel:: Leg1BeginOverhangSelection |
Uses the hsSelection codelist in the HS_S3DAssy_Codelist.xls workbook to select Leg1BeginOverhang by either input or rule. |
By Rule - 1 - Leg1BeginOverhangRule is used By Input - 2 - Leg1BeginOverhangValue is used |
IJUAhsLeg1EndOH:: |
Specifies a positive number for the distance between the first leg and the supporting structure. |
The following values are supported: 1 - Far Edge of Steel 2 - Centerline of Steel 3 - Near Edge of Steel |
IJUAhsLeg1EndOHRl:: Leg1EndOverhangRule |
Defines an HgrSupportRule that returns the distance that the first leg should overhang past the supporting object. The hanger rule must exist in the catalog; it can be a rule name or a ProgID. To select the value of the overhang directly using Leg1EndOverhangValue, do not type any value for this property. |
|
IJUAhsLeg1EndOHDef:: Leg1EndOverhangDefinition |
Defines how the end overhang should be measured with respect to the supporting object. If you do not type any value, a default value of 1 is used. |
The following values are allowed: 1 - Far Edge of Steel 2 - Centerline of Steel 3 - Near Edge of Steel |
IJUAhsLeg1EndOHSel:: Leg1EndOverhangSelection |
Uses the hsSelection Codelist in the HS_S3DAssy_Codelist.xls workbook to select Leg1EndOverhang by either input or rule. |
Allowed values are: By Rule - 1 - Leg1EndOverhangRule is used By Input - 2 - Leg1EndOverhangValue is used |
IJUAhsCapPlate1:: |
Specifies the part number or the part class of a Plate part to use for a support. |
The Cap Plate is an optional part. To exclude a Cap Plate, do not enter any value for these attributes. |
IJUAhsCapPlate1Rl:: CapPlate1Rule |
Defines an HgrSupportRule that returns a part number or part class to use for the cap plate. The hanger rule must exist in the catalog; it can be a rule name or a ProgID. To specify the part directly using CapPlate1Part, do not type any value for this property. CapPlate1Rule can also be used to specify a custom part selection rule. If both CapPlate1Part and CapPlate1Rule are populated, then it is assumed that CapPlate1Rule is a part selection rule, which is then used to override the default part selection rule defined in the catalog for the part class specified in CapPlate1Part. |
|
IJUAhsCapPlate1Ang:: CapPlate1Angle |
Specifies the angle of rotation for the Cap Plate about the axis of the Box Frame. |
Leg2 and CapPlate2 Attributes
The Leg 2 attributes display the same behavior as the Leg 1 attributes.