Super assemblies are defined by the top-level sheets, describe the general support attributes, and call out the sub-assemblies such as top, middle, and bottom sub-assemblies.
Single Rod Hanger Attributes
The following graphic illustrates a Single Rod Hanger:
The following table illustrates the properties of a Single Rod Hanger:
Name |
User Name |
OA |
Category |
On Property Page |
Read Only |
---|---|---|---|---|---|
Angle |
Structure Attachment Rotation |
Yes |
Dimensions |
Yes |
No |
WithTurnbuckle |
With Turnbuckle |
Yes |
Dimensions |
Yes |
No |
URS_AxialOffset |
Axial Offset |
Yes |
Dimensions |
Yes |
No |
URS_LateralOffset |
Lateral Offset |
Yes |
Dimensions |
Yes |
No |
OffsetZ |
Z Offset |
Yes |
Dimensions |
Yes |
No |
Attribute Name |
Description |
Implementation Details |
---|---|---|
IJUAHgrURS_RHRotation:: Angle |
Specifies a codelist value for the rotation of the structure attachment around the rod. |
hsSteelOrientationAngle 0, 90, 180, and 270 degrees. |
IJUAHgrURS_WithTurnbuckle:: WithTurnbuckle |
Toggles the Turnbuckle on or off. |
Turnbuckle. False does not include Turnbuckle. |
IJOAHgrURS_AxialOffset:: URS_AxialOffset |
Specifies the offset for the top part along the pipe centerline. For more information, see Axial lateral offset in the same section. |
|
IJOAHgrURS_LateralOffset:: URS_LateralOffset |
Specifies the lateral offset for the top part from the pipe centerline. For more information, see Axial lateral offset in the same section. |
|
IJUAHsOffsetZ::OffsetZ |
Specifies the offset value for the bottom part of the support from the pipe. This attribute is used when no bottom type exists. For example, Pipe Lug hanger does not need a bottom type if IJUAHgrURS_RH_PipeAtt::PipeAtt is left blank in Rigid Bottom sub-assembly. |
Double Rod Hanger Attributes
The following graphic illustrates a Double Rod Hanger:
The following graphic illustrates the properties of a Double Rod Hanger:
Attribute Name |
Description |
Implementation Details |
---|---|---|
IJUAHgrURS_DblRHRotation:: Angle1 |
Specifies a codelist value for the rotation of the structure attachment 1 around the rod. |
hsSteelOrientationAngle 0, 90, 180, and 270 deg |
IJUAHgrURS_DblRHRotation:: Angle2 |
Specifies a codelist value for the rotation of the structure attachment 2 around the rod. |
hsSteelOrientationAngle 0, 90, 180, and 270 deg |
IJUAHgrURS_WithTurnbuckle:: WithTurnbuckle |
Toggles the Turnbuckle on or off. |
For example: True includes Turnbuckle. False does not include Turnbuckle. |
IJOAHgrURS_AxialOffset:: URS_AxialOffset |
Specifies the offset for the top part along the pipe centerline. |
For more information, see Axial lateral offset. |
IJOAHgrURS_LateralOffset:: URS_LateralOffset1 |
Specifies the lateral offset for the top part 1 from the pipe centerline. |
|
IJOAHgrURS_LateralOffset:: URS_LateralOffset2 |
Specifies the lateral offset for the top part 2 from the pipe centerline. |
Riser Configuration Attributes
The following graphic illustrates a Riser Rod Hanger support:
The following graphic illustrates the properties of a Riser Rod Hanger support:
Attribute Name |
Description |
Implementation Details |
---|---|---|
IJUAHgrOrientation:: OrientationAngle |
Specifies the angle that the Riser Clamp rotates around the pipe |
|
IJOAHgrURS_RiserSpan:: RiserSpan |
Specifies the pin-to-pin distance of the Riser Clamp. |
|
IJOAHgrURS_RiserSpan:: PinOverhang |
Specifies the pin-to-edge distance of the Riser Clamp. |
Trapeze Configuration Attributes
The following graphic illustrates a Trapeze Rod Hanger:
The following graphic illustrates the properties of a Trapeze Rod Hanger:
Attribute Name |
Description |
Implementation Details |
|
---|---|---|---|
IJUAhsMirrorTrap:: MirrorTrap |
Specifies the value for the Trapeze mirror about the bounding box. |
Use the following values: |
|
IJUAhsIncludeInsulation:: IncludeInsulation |
Specifies whether the Trapeze must adjust the size to include pipe insulation. |
Supported values: |
|
IJUAhsTrapOffset1:: Offset1Value IJUAhsTrapOffset2:: Offset2Value |
Specifies the offset distance for the first rod from the pipe. |
Use the following 1 - Inside Rod to Edge of Pipe 3 - Outside Rod to Edge of Pipe 5 - Inside Rod to Pipe CL 7 - Outside Rod to Pipe CL |
definitions: 2 - Center of Rod to Edge of Pipe 4 - End of Steel to Edge of Pipe 6 - Center Rod to Pipe CL 8 - End of Steel to Pipe CL |
IJUAhsTrapShoeHeight:: ShoeHeightValue |
Specifies the offset distance from the pipe to the Trapeze. |
Use the following definitions: 1 - Edge of Boundary Pipe (Edge of BBX) 2 - Center of Primary Pipe |
|
IJUAhsTrapBeginOH:: TrapBeginOverhangValue IJUAhsTrapEndOH:: TrapEndOverhangValue |
Specifies the distance that the Trapeze must overhang past the first rod. |
Use the following definitions: 1 - External Edge of Rod 2 - Centerline of Rod 3 - Internal Edge of Rod |
|
IJUAhsTrapSpan::SpanValue |
Specifies the Trapeze span. |
Use the following definitions: 1 - Inside Edge of Rods 2 - Centerline of Rods 3 - Outside Edge of Rods 4 - Steel Length |
|
IJOAHgrURS_BackToBack:: BBGap |
Specifies the distance between the back to back sections in the Trapeze. |
Spring Configuration Attributes
The following graphic illustrates the properties of Variable and Constant Spring parts of the Rod Hanger support:
Attribute Name |
Description |
Implementation Details |
---|---|---|
IJUAHgrURS_Spring:: SpringAssembly |
Specifies the Spring Assembly name that you must use for the support. This value is used as the first part of the part number for the middle sub-assembly. |
For example, SpringAssembly = ConstantHangerMiddle- SpringType = A part number = ConstantHangerMiddle-A |
IJUAHgrURS_Spring:: SpringType |
Specifies the Spring Type that you must use for the support. This value is used as the first part of the part number for the middle sub-assembly. |
|
IJUAHgrURS_Spring::TotalLoad |
Specifies the total load. For more information, see the 3D SmartParts Configuration Reference. |
|
IJUAHgrURS_Spring::TotalTravel |
Specifies the total travel. |
|
IJUAHgrURS_Spring:: ActualTravel |
Specifies the actual travel. |
|
IJUAHgrURS_Spring::TravelDir |
Specifies the direction of the spring movement. |
hsSpringMovementDir 1 = Up 2 = Down |
IJUAHgrURS_Spring::ColdLoad |
Specifies the cold load value for the Variable Springs only. |
|
IJUAHgrURS_Spring::Variation |
Specifies the variation for the Variable Springs only. |
|
IJUAHgrURS_ConstantSpring:: ConstantSpringPart |
Specifies the Constant Spring part class name for the constant hangers only. |
hsConstatnSpringPart codelist. |
IJUAHgrURS_VariableSpring:: VariableSpringPart |
Specifies the Variable Spring part class name for variable hangers only. |
hsVariableSpringPart codelist. |
IJUAHgrURS_SpringSize:: SpringSize |
Specifies the size of the spring part for the support. |