Beam Dimension Attributes - Intergraph Smart Reference Data Standard Database - Version 12.4 - Help - Hexagon

BeamOffset

Beam Offset

Dimensions

Yes

No

BeamOffsetRl

Beam Offset - Rule

Dimensions

Yes

No

BeamOffsetSel

Beam Offset - Selection

Dimensions

Yes

No

BBGap

Back To Back Gap

Dimensions

Yes

No

BBGapRl

Back To Back Gap - Rule

Dimensions

Yes

No

BBGapSel

Back To Back Gap - Selection

Dimensions

Yes

No

BeamEndOffset (1&2)

Beam End Offset (1&2)

Dimensions

Yes

No

BeamEndOffsetRl (1&2)

Beam End Offset (1&2) -
Rule

Dimensions

Yes

No

BeamEndOffsetSel
(1&2)

Beam End Offset (1&2) -
Selection

Dimensions

Yes

No

ClipLength (1&2)

Clip Length (1&2)

Dimensions

Yes

No

ClipLengthRl (1&2)

Clip Length (1&2) -
Rule

Dimensions

Yes

No

ClipLengthSel (1&2)

Clip Length (1&2) -
Selection

Dimensions

Yes

No

VertPltOH (1&2)

Vertical Plate Overhang
(1&2)

Dimensions

Yes

No

VertPltOHRl (1&2)

Vertical Plate Overhang
(1&2) - Rule

Dimensions

Yes

No

VertPltOHSel (1&2)

Vertical Plate Overhang
(1&2) - Selection

Dimensions

Yes

No

IJUAhsBeamOffset::
BeamOffset

Specifies the offset of the Beam to Beam support from the primary supporting structure.

The offset definition depends on the primary Beam connection value.

Use the following values:

1 - Above

2 - Top

3 - Top Inside

4 - Center

5 - Bottom Inside

6 - Bottom

7 - Below

8 - Vertical Plate

IJUAhsBBGap::BBGap

Specifies the gap between the back-to-back beams.

IJUAhsEndOffset1::
EndOffset1

Specifies the offset from the end of beam.

BeamEndOffset1 applies to the beam end that is connected to the primary supporting structure.

The offset definition depends on the primary beam connection value.

1 - Above

2 - Top

3 - Top Inside

4 - Center

5 - Bottom Inside

6 - Bottom

7 - Below

8 - Vertical Plate

IJUAhsEndOffset2::
EndOffset2

Specifies the offset from the end of the beam.

BeamEndOffset2 applies to the end of the beam that is connected to the secondary supporting structure.

The offset definition depends on the secondary beam connection value.

1 - Web

2 - Flange

3 - Vertical Plate

IJUAhsClipLen1::
ClipLength1

IJUAhsClipLen2::
ClipLength2

Specifies the length of the Clip.

ClipLength1 specifies the length of Clip 1 and ClipLength2 specifies the length of Clip 2.

IJUAhsVertPltOH1::
VertPlateOverhang1

IJUAhsVertPltOH2::
VertPlateOverhang2

Specifies the overhang of the vertical Plate from the bottom of the Beam.

VertPlateOverHang1 specifies the overhang of the vertical Plate 1.

VertPlateOverhang2 specifies the overhang of vertical Plate 2.

IJUAhsFrameShoeHeight::ShoeHeightValue

Specifies the distance from pipe bottom surface to support top surface.This is applicable for vertical structures and horizontal pipe configuration.

IJUAhsFrameShoeHeightRl::ShoeHeightRule

Specifies a rule that returns shoeHeight value.

IJUAhsFrameShoeHeightSel::ShoeHeightSelection

Overrides the codelist value that determines the origin of the selection. This property uses the hsSelection codelist.

hsSelection:

1 - By Rule

2- By Input

BeamSpan

Beam Span

Dimensions

Yes

Yes

VerticalPlate1Length

Vertical Plate 1 Length

Dimensions

Yes

No

VerticalPlate2Length

Vertical Plate 2 Length

Dimensions

Yes

No

IJUAhsBeamSpan::
BeamSpan

Specifies the span of the Beam to Beam support.

Span is the measurement between the centers of the Flanges of each supporting structure.

IJUAhsVertPlt1Len::
VertPlate1Length

IJUAhsVertPlt2Len::
VertPlate2Length

Specifies the lengths of the vertical Plates, if included.

VerticalPlate1Length specifies the length of the vertical Plate connected to the primary supporting structure.

VerticalPlate2Length specifies the length of the vertical Plate connected to the secondary supporting structure.

If one or both vertical Plates is not included in the support, then the corresponding attribute values are set to zero.