A Cantilever support uses the following part attributes:
Attribute Name |
Description |
Implementation Details |
---|---|---|
IJUAhsMember1::Member1Part |
Specifies the part number or the part class of the first support member to use for the support. |
Option 1 - Specify a part number or part class directly. Option 2 - Use HgrRule to get the part. The base support is a mandatory part. Specify either a Member1Part or Member1Rule. |
IJUAhsMember1Rl::Member1Rule |
Specifies the hgrSupportRule that returns the part number for the hanger beam pipe. The hanger rule must be the name of an existing rule in the catalog. |
|
IJUAhsMember1Ang::Member1OrientationAngle |
Specifies the angle of rotation about the axis of the leg for the first member of the support. |
hsSteelOrientalAngle: |
IJUAhsMember2::Member2Part |
Specifies the part number or the part class of the first support member to use for the support. |
Option 1 - Specify a part number or part class directly. Option 2 - Use HgrRule to get the part. The base support is a mandatory part. Specify either a Member1Part or Member1Rule. |
IJUAhsMember2Rl::Member2Rule |
Specifies the hgrSupportRule that returns the part number for the hanger beam pipe. The hanger rule must be the name of an existing rule in the catalog. |
|
IJUAhsMember2Ang::Member2OrientationAngle |
Specifies the angle of rotation about the axis of the leg for the first member of the support. |
hsSteelOrientalAngle: |
IJUAhsMember2Len:: Member2Length |
Specifies the length for the member2 support. |
|
IJUAhsMember1EndOH:: Member1EndOverhangValue |
Specifies the distance that the first member overhangs past the first leg. To select the overhang using Member1EndOverhangRule, do not specify any value for this property. |
|
IJUAhsMember1EndOHRl:: Member1EndOverhangRule |
Specifies the hgrSupportRule that returns the distance. The hanger rule must be the name of an existing rule in the catalog. |
|
IJUAhsMember1EndOHDef::Member1EndOverhangDefinition |
Defines how the EndOverhang is measured. |
|
IJUAhsMember1EndOHSel::Member1EndOverhangSelection |
Uses the hsSelection codelist in the HS_S3DAssy_Codelist.xls workbook to select the Member1EndOverhang by either input or rule |
Option 1: By Rule Member1EndOverhangRule is used Option 2: By Input Member1EndOverhangValue is used |
IJUAhsCapPlate1::CapPlate1Part |
Specifies the part number or the part class for the plate placed at the end of the main section and at the end connected to the member. You must select a Smart-Part 2 Port Plate. To select the part using CapPlate1Rule, do not type any value for this property. |
|
IJUAhsCapPlate1Rl::CapPlate1Rule |
Specifies the hgrSupportRule that returns the part number for the hanger beam pipe. The hanger rule must be the name of an existing rule in the catalog. |
|
IJUAhsCapPlate1Ang::CapPlate1Angle |
Specifies the angle that CapPlate1 should be rotated about the Z-axis of the port to which the plate is attached. |
|
IJUAhsCapHorOffset::CapHorOffset |
Specifies the offset by which the cap plate is moved horizontally. |
|
IJUAhsCapVerOffset::CapVerOffset |
Specifies the offset by which the cap plate is moved vertically. |
|
IJUAhsLeg1::Leg1Part |
Specifies the steel part number for the first support leg. To select the part number using Leg1Rule, do not type any value for this property. |
|
IJUAhsLeg1Rl::Leg1Rule |
Defines an HgrSupportRule that returns a rich hanger beam part number. To select the part number using Leg1Part, do not type any value for this property. |
|
IJUAhsLeg1Ang::Leg1OrientationAngle |
Specifies the angle of rotation about the axis of the leg for the first member of the support. |
hsSteelOrientalAngle: |
IJUAhsBraceAngle::BraceAngle |
Specifies the angle at which the brace is connected to the structure. BraceAngle accepts only positive values less than or equal to 60 degrees. |
|
IJUAhsBraceHorOff::BraceHorOffset |
Specifies the distance by which the brace is offset horizontally from the edge of the plate. |
|
IJUAhsBraceOffDef::BraceOffsetDef |
Specifies how the BraceHorOffset is measured. |
The following values are allowed 1 - From the edge of the horizontal member to the Brace end. 2 - From the center of pipe to the Brace end 3 - From edge of pipe to Brace end 4 - From edge of horizontal member to intersection of centerlines |
IJUAhsFrPipeAtt1::PipeAtt1Part |
Specifies the part number or part class for the first pipe attachment. To select the part number using PipeAtt1Rule, do not type any value for this property. |
|
IJUAhsFrPipeAtt1Rl::PipeAtt1Rule |
Defines an HgrSupportRule that returns a rich hanger beam part number. To select the part number using PipeAtt1Part, do not type any value for this property. |
|
IJUAhsFrPipeAtt1Qty::PipeAtt1Quantity |
Specifies the number of PipeAtt1Parts to be included in the support. In general the quantity is either 1 or 2. |
|
IJUAhsFrPipeAtt1Offset::PipeAtt1Offset |
Specifies the offset value for PipeAtt1Part along the pipe. |
|
IJUAhsFrPipeAtt2::PipeAtt1Part |
Specifies the part number or part class for the first pipe attachment. To select the part number using PipeAtt3Rule, do not type any value for this property. |
|
IJUAhsFrPipeAtt1Rl::PipeAtt2Rule |
Defines an HgrSupportRule that returns a rich hanger beam part number. To select the part number using PipeAtt2Part, do not type any value for this property. |
|
IJUAhsFrPipeAtt3Qty::PipeAtt3Quantity |
Specifies the number of PipeAtt3Parts to be included in the support. In general the quantity is either 1 or 2. |
|
IJUAhsFrPipeAtt2Offset::PipeAtt1Offset |
Specifies the offset value for PipeAtt2Part along the pipe. |
|
IJUAhsBasePlate1::BasePlate1Part |
Specifies the part number or part class of the first base plate. To select the part using BasePlate1Rule, do not type any value for this property. |
|
IJUAhsBasePlate1Rl::BasePlate1Rule |
Defines an HgrSupportRule that returns a part number or part class to use for the base plate. To select the part directly using BasePlate1Part, do not type any value for this property. |
|
IJUAhsBasePlate1Ang::BasePlate1Angle |
Specifies the angle that BasePlate1 should be rotated about the Z-axis of the port to which the plate is attached. |
|
IJUAhsBasePlate1Off::BasePlate1Offset |
Specifies the distance by which the base plate should be offset from leg1. BasePlate1Offset is applicable only when StructureConnection is set to either Lapped or Lapped-Opposite. |
|
IJUAhsBasePlate2Off::BasePlate2Offset |
Specifies the distance by which the base plate should be offset from leg2. BasePlate2Offset is applicable only when StructureConnection is set to either Lapped or Lapped-Opposite. |
|
IJUAhsBasePlate1OffDef::BasePlate1OffsetDef |
Defines how BasePlate1Offset is measured. BasePlate1OffsetDef specifies the distance between the base plate and leg1. |
|
IJUAhsBasePlate2OffDef::BasePlate2OffsetDef |
Defines how BasePlate2Offset is measured. BasePlate1OffsetDef specifies the distance from the center of the base plate to the edge of leg2. |
|
IJUAhsBolt1::Bolt1Part |
Specifies the part number or the part class of the bolts connected to BasePlate1. To select the part using Bolt1Rule, do not type any value for this property. |
|
IJUAhsBolt1Rl::Bolt1Rule |
Defines an HgrSupportRule that returns a part number or the part class to use for the Bolts. To specify the part directly using Bolt1Part, do not type any value for this property. |
|
IJUAhsBolt1Qty::Bolt1Quantity |
Specifies the quantity of bolts to include on BasePlate1. Usually, 2 or 4. The following properties are applicable for all frame types: |
|
IJUAhsBolt1Offset1::Bolt1Offset1 |
Specifies the offset value for Bolt1Part from the edge of the plate to the center of the bolt along the x-axis of the pipe. |
|
IJUAhsBolt1Offset2::Bolt1Offset2 |
Specifies the offset value for Bolt1Part from the edge of the plate to the center of the bolt along the y-axis of the pipe. |
|
IJUAhsFrameOffset1::Offset1Value |
Specifies the distance that the member should be offset from the pipe. To select the offset value using Offset1Rule, do not type any value for this property. |
|
IJUAhsFrameOffset1Rl::Offset1Rule |
Defines an HgrSupportRule that returns the offset from the member to the pipe. To select the offset value using Offset1Value, do not type any value for this property. |
|
IJUAhsFrameOffset1Def::Offset1Definition |
Specifies how Offset1 should be measured. If you type an unsupported value or do not assign a value, then the software uses the default value that is 1. |
|
IJUAhsFrameOffset1Sel::Offset1Selection |
Uses the hsSelection codelist in the HS_S3DAssy_Codelist.xls workbook to select Offset1 by either input or rule. |
By Rule - 1 – Offset1Rule is used By Input - 2 – Offset1Value is used |
IJUAhsFrameShoeHeight::ShoeHeightValue |
Specifies the distance that the main steel member should be offset from the pipe. To determine the shoe height using ShoeHeightRule, do not type any value for this property. |
|
IJUAhsFrameShoeHeightRl::ShoeHeightRule |
Defines an HgrSupportRule that returns the shoe height. To determine the shoe height using ShoeHeightValue, do not type any value for this property. |
|
IJUAhsFrameShoeHeightDef::ShoeHeightDefinition |
Specifies how ShoeHeight should be measured. If you type an unsupported value or do not assign any value, then the software uses the default value that is 1. |
|
JUAhsFrameShoeHeightSel::ShoeHeightSelection |
Uses the hsSelection codelist in the HS_S3DAssy_Codelist.xls workbook to select ShoeHeightValue by either input or rule. |
By Rule - 1 – Offset1Rule is used By Input - 2 – Offset1Value is used |
IJUAhsFrameLength1::Length1Value |
Specifies the length of the first leg after the support is placed. This property is set by the AIR and can be used for reporting purposes or for the support validation. |
|
IJUAhsFrameLength1Def::Length1Definition |
Defines where the length should be measured from. This property sets the definition of Length1Value. |
End of Steel End of Plate Pipe Center line |
IJUAhsFrameLength2::Length2Value |
Specifies the length of the brace leg after the support has been placed. This property is set by the AIR and can be used for reporting purposes or for support validation. |
|
IJUAhsFrameLength2Def::Length2Definition |
Defines where the length should be measured from. This property sets the definition of Length2Value. |
1 – Length 2 - Cut Length |
IJUAhsSuppPosOffset::SupPosOff |
Specifies the support distance from origin of the support. To determine the support position offset using SupPosOffRl, do not type any value for this property. |
|
IJUAhsSuppPosOffsetRl::SupPosOffRl |
Defines a HgrSupportRule that returns the support position offset. The hanger rule name or the ProgID must exist in the catalog. To determine the support position using SupPosOff, do not type any value for this property. |
For more information on how to use part specification attributes, see Part Specifications of Common Attributes section.